ZHCSHK8E october   2017  – july 2023 TAS2770

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Timing Requirements
    7. 6.7 TDM Port Timing Requirements
    8. 6.8 PDM Port Timing Requirements
    9. 6.9 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Device Mode and Address Selection
      2. 8.3.2 General I2C Operation
      3. 8.3.3 Single-Byte and Multiple-Byte Transfers
      4. 8.3.4 Single-Byte Write
      5. 8.3.5 Multiple-Byte Write and Incremental Multiple-Byte Write
      6. 8.3.6 Single-Byte Read
      7. 8.3.7 Multiple-Byte Read
      8. 8.3.8 Register Organization
    4. 8.4 Device Functional Modes
      1. 8.4.1  PDM Input
      2. 8.4.2  TDM Port
      3. 8.4.3  Playback Signal Path
        1. 8.4.3.1 High Pass Filter
        2. 8.4.3.2 Digital Volume Control and Amplifier Output Level
        3. 8.4.3.3 Audio Playback Selection
        4. 8.4.3.4 Battery Tracking Limiter with Brown Out Prevention
        5. 8.4.3.5 Inter Chip Limiter Alignment
          1. 8.4.3.5.1 TDM Mode
        6. 8.4.3.6 Class-D Settings
      4. 8.4.4  SAR ADC
      5. 8.4.5  IV Sense
      6. 8.4.6  Clocks and PLL
      7. 8.4.7  Operational Modes
        1. 8.4.7.1 Hardware Shutdown
        2. 8.4.7.2 Software Shutdown
        3. 8.4.7.3 Mute
        4. 8.4.7.4 Active
        5. 8.4.7.5 Mode Control and Software Reset
      8. 8.4.8  Faults and Status
      9. 8.4.9  Power Sequencing Requirements
      10. 8.4.10 Digital Input Pull Downs
    5. 8.5 Register Maps
      1. 8.5.1 Register Summary Table Book=0x00 Page=0x00
      2. 8.5.2 Register Maps
        1. 8.5.2.1  PAGE (book=0x00 page=0x00 address=0x00) [reset=0h]
        2. 8.5.2.2  SW_RESET (book=0x00 page=0x00 address=0x01) [reset=0h]
        3. 8.5.2.3  PWR_CTL (book=0x00 page=0x00 address=0x02) [reset=Eh]
        4. 8.5.2.4  PB_CFG0 (book=0x00 page=0x00 address=0x03) [reset=10h]
        5. 8.5.2.5  PB_CFG1 (book=0x00 page=0x00 address=0x04) [reset=1h]
        6. 8.5.2.6  PB_CFG2 (book=0x00 page=0x00 address=0x05) [reset=0h]
        7. 8.5.2.7  PB_CFG3 (book=0x00 page=0x00 address=0x06) [reset=0h]
        8. 8.5.2.8  MISC_CFG (book=0x00 page=0x00 address=0x07) [reset=6h]
        9. 8.5.2.9  PDM_CFG0 (book=0x00 page=0x00 address=0x08) [reset=0h]
        10. 8.5.2.10 PDM_CFG1 (book=0x00 page=0x00 address=0x09) [reset=8h]
        11. 8.5.2.11 TDM_CFG0 (book=0x00 page=0x00 address=0x0A) [reset=7h]
        12. 8.5.2.12 TDM_CFG1 (book=0x00 page=0x00 address=0x0B) [reset=2h]
        13. 8.5.2.13 TDM_CFG2 (book=0x00 page=0x00 address=0x0C) [reset=Ah]
        14. 8.5.2.14 TDM_CFG3 (book=0x00 page=0x00 address=0x0D) [reset=10h]
        15. 8.5.2.15 TDM_CFG4 (book=0x00 page=0x00 address=0x0E) [reset=13h]
        16. 8.5.2.16 TDM_CFG5 (book=0x00 page=0x00 address=0x0F) [reset=2h]
        17. 8.5.2.17 TDM_CFG6 (book=0x00 page=0x00 address=0x10) [reset=0h]
        18. 8.5.2.18 TDM_CFG7 (book=0x00 page=0x00 address=0x11) [reset=4h]
        19. 8.5.2.19 TDM_CFG8 (book=0x00 page=0x00 address=0x12) [reset=6h]
        20. 8.5.2.20 TDM_CFG9 (book=0x00 page=0x00 address=0x13) [reset=7h]
        21. 8.5.2.21 TDM_CFG10 (book=0x00 page=0x00 address=0x14) [reset=8h]
        22. 8.5.2.22 LIM_CFG0 (book=0x00 page=0x00 address=0x15) [reset=14h]
        23. 8.5.2.23 LIM_CFG1 (book=0x00 page=0x00 address=0x16) [reset=76h]
        24. 8.5.2.24 LIM_CFG2 (book=0x00 page=0x00 address=0x17) [reset=10h]
        25. 8.5.2.25 LIM_CFG3 (book=0x00 page=0x00 address=0x18) [reset=6Eh]
        26. 8.5.2.26 LIM_CFG4 (book=0x00 page=0x00 address=0x19) [reset=1Eh]
        27. 8.5.2.27 LIM_CFG5 (book=0x00 page=0x00 address=0x1A) [reset=58h]
        28. 8.5.2.28 BOP_CFG0 (book=0x00 page=0x00 address=0x1B) [reset=1h]
        29. 8.5.2.29 BOP_CFG1 (book=0x00 page=0x00 address=0x1C) [reset=14h]
        30. 8.5.2.30 BOP_CFG2 (book=0x00 page=0x00 address=0x1D) [reset=4Eh]
        31. 8.5.2.31 ICLA_CFG0 (book=0x00 page=0x00 address=0x1E) [reset=0h]
        32. 8.5.2.32 ICLA_CFG1 (book=0x00 page=0x00 address=0x1F) [reset=0h]
        33. 8.5.2.33 INT_MASK0 (book=0x00 page=0x00 address=0x20) [reset=FCh]
        34. 8.5.2.34 INT_MASK1 (book=0x00 page=0x00 address=0x21) [reset=B1h]
        35. 8.5.2.35 INT_LIVE0 (book=0x00 page=0x00 address=0x22) [reset=0h]
        36. 8.5.2.36 INT_LIVE1 (book=0x00 page=0x00 address=0x23) [reset=0h]
        37. 8.5.2.37 INT_LTCH0 (book=0x00 page=0x00 address=0x24) [reset=0h]
        38. 8.5.2.38 INT_LTCH1 (book=0x00 page=0x00 address=0x25) [reset=0h]
        39. 8.5.2.39 INT_LTCH2 (book=0x00 page=0x00 address=0x26) [reset=0h]
        40. 8.5.2.40 VBAT_MSB (book=0x00 page=0x00 address=0x27) [reset=0h]
        41. 8.5.2.41 VBAT_LSB (book=0x00 page=0x00 address=0x28) [reset=0h]
        42. 8.5.2.42 TEMP_MSB (book=0x00 page=0x00 address=0x29) [reset=0h]
        43. 8.5.2.43 TEMP_LSB (book=0x00 page=0x00 address=0x2A) [reset=0h]
        44. 8.5.2.44 INT_CFG (book=0x00 page=0x00 address=0x30) [reset=5h]
        45. 8.5.2.45 DIN_PD (book=0x00 page=0x00 address=0x31) [reset=0h]
        46. 8.5.2.46 MISC_IRQ (book=0x00 page=0x00 address=0x32) [reset=81h]
        47. 8.5.2.47 CLOCK_CFG (book=0x00 page=0x00 address=0x3C) [reset=Dh]
        48. 8.5.2.48 TDM_DET (book=0x00 page=0x00 address=0x77) [reset=7Fh]
        49. 8.5.2.49 REV_ID (book=0x00 page=0x00 address=0x7D) [reset=20h]
        50. 8.5.2.50 I2C_CKSUM (book=0x00 page=0x00 address=0x7E) [reset=0h]
        51. 8.5.2.51 BOOK (book=0x00 page=0x00 address=0x7F) [reset=0h]
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Overview
        2. 9.2.2.2 Select Input Capacitance
        3. 9.2.2.3 Select Decoupling Capacitors
        4. 9.2.2.4 Select Bootstrap Capacitors
      3. 9.2.3 Application Curves
    3. 9.3 Initialization Set Up
      1. 9.3.1 Initial Device Configuration - Auto Rate
      2. 9.3.2 Initial Device Configuration - 48 kHz
      3. 9.3.3 Initial Device Configuration - 44.1 kHz
      4. 9.3.4 Sample Rate Change - 48 kHz to 44.1kHz
      5. 9.3.5 Sample Rate Change - 44.1 kHz to 48 kHz
      6. 9.3.6 Device Mute
      7. 9.3.7 Device Un-Mute
      8. 9.3.8 Device Sleep
      9. 9.3.9 Device Wake
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 Community Resources
    3. 12.3 Trademarks
  14. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息
8.4.3.5.1 TDM Mode

The TAS2770 supports alignment of limiter (including brown out prevention) dynamics across devices that share the same TDM bus. This ensures consistent gain between channels during limiting or brown out events since these dynamics are dependent on audio content, which can vary across channels. Each device can be configured to align to a specified number of other devices, which allows creation of groupings of devices that align only to each other.

Limiter activity is communicated through the limiter gain reduction parameter that can be optionally transmitted by each device on SDOUT in an 8-bit time slot. Gain reduction should be transmitted in adjacent time slots for all devices that are to be aligned beginning with the first slot that is specified by the ICLA_SLOT[5:0] register bits. The order of the devices is not important as long as they are adjacent. The time slot for limiter gain reduction is configured by the GAIN_SLOT[5:0] register bits and enabled by the GAIN_TX register bit.

The ICLA_SEN[7:0] register bits specify which time slots should be listened to for gain alignment. This allows any number of devices between two and eight to be grouped together. At least two of these bits should be enabled for alignment to take place. The ICLA_USE_MAX register bit determines whether alignment is based on the maximum or minimum gain reduction value from the group of enabled devices.

To enable the inter chip limiter alignment feature, the ICLA_EN register bit should be asserted high and all devices should be configured with identical limiter and brown out prevention settings. Limiter gain reduction transmission should be enabled on all devices as described above.

Table 8-63 Inter Chip Limiter Alignment
ICLA_ENValue
0
Disabled (default)
1
Enabled
Table 8-64 ICLA Alignment Configuration
ICLA_MODEValue
00
Use the minimum gain reduction of the ICLA group including 0dB (default)
01
Use the maximum gain reduction of the ICLA group
10
Use the minimum gain reduction of the ICLA group that is non-0dB
11
Reserved
Table 8-65 Inter Chip Limiter Alignment Starting Time Slot
ICLA_SLOT[5:0]Starting Time Slot
0x00
Time Slot 0 (default)
0x01
Time Slot 1
0x02
Time Slot 2
...
...
0x3F
Time Slot 63
Table 8-66 Inter Chip Limiter Alignment Time Slot Enable
Register BitDescriptionBit ValueState
ICLA_SEN[0]Time Slot = ICLA_SLOT[5:0]. When enabled, the limiter will include this time slot in the alignment group.
0
Disabled (default)
1
Enabled
ICLA_SEN[1]Time Slot = ICLA_SLOT[5:0] + 1. When enabled, the limiter will include this time slot in the alignment group.
0
Disabled (default)
1
Enabled
ICLA_SEN[2]Time Slot = ICLA_SLOT[5:0] + 2. When enabled, the limiter will include this time slot in the alignment group.
0
Disabled (default)
1
Enabled
ICLA_SEN[3]Time Slot = ICLA_SLOT[5:0] + 3. When enabled, the limiter will include this time slot in the alignment group.
0
Disabled (default)
1
Enabled
ICLA_SEN[4]Time Slot = ICLA_SLOT[5:0] + 4. When enabled, the limiter will include this time slot in the alignment group.
0
Disabled (default)
1
Enabled
ICLA_SEN[5]Time Slot = ICLA_SLOT[5:0] + 5. When enabled, the limiter will include this time slot in the alignment group.
0
Disabled (default)
1
Enabled
ICLA_SEN[6]Time Slot = ICLA_SLOT[5:0] + 6. When enabled, the limiter will include this time slot in the alignment group.
0
Disabled (default)
1
Enabled
ICLA_SEN[7]Time Slot = ICLA_SLOT[5:0] + 7. When enabled, the limiter will include this time slot in the alignment group.
0
Disabled (default)
1
Enabled