SLLS545G November   2002  – October 2015 SN55HVD251 , SN65HVD251

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Supply Current
    6. 6.6  Electrical Characteristics: Driver
    7. 6.7  Electrical Characteristics: Receiver
    8. 6.8  VREF-Pin Characteristics
    9. 6.9  Power Dissipation Characteristics
    10. 6.10 Switching Characteristics: Driver
    11. 6.11 Switching Characteristics: Device
    12. 6.12 Switching Characteristics: Receiver
    13. 6.13 Dissipation Ratings
    14. 6.14 Typical Characteristics
  7. 7 Parameter Measurement Information
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Mode Control
      2. 8.3.2 High-Speed Mode
      3. 8.3.3 Slope Control Mode
      4. 8.3.4 Low-Power Mode
      5. 8.3.5 Thermal Shutdown
    4. 8.4 Device Functional Modes
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Bus Loading, Length, and Number of Nodes
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 CAN Termination
        2. 9.2.2.2 Loop Propagation Delay
      3. 9.2.3 Application Curve
    3. 9.3 System Example
      1. 9.3.1 ISO 11898 Compliance of HVD251 5-V CAN Bus Transceiver
        1. 9.3.1.1 Introduction
        2. 9.3.1.2 Differential Signal
        3. 9.3.1.3 Common-Mode Signal
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Related Links
    2. 12.2 Community Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6 Specifications

6.1 Absolute Maximum Ratings(1)(2)

MIN MAX UNIT
Supply voltage, VCC –0.3 7 V
Voltage at any bus pin(CANH or CANL) –36 36 V
Transient voltage per ISO 7637, pulse 1, 2, 3a, 3b CANH, CANL –200 200 V
Input voltage, VI (D, Rs, or R) –0.3 VCC + 0.5 V
Receiver output current, IO –10 10 mA mA
Electrical fast transient/burst IEC 61000-4-4, Classification B CANH, CANL –3 3 kV
Continuous total power dissipation (see Dissipation Ratings)
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, except differential I/O bus voltages, are with respect to network ground pin.

6.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) All pins ±6000 V
CANH, CANL and GND ±14000
Charged-device model (CDM), per JEDEC specification JESD22-C101(2) ±1000
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

6.3 Recommended Operating Conditions

MIN NOM MAX UNIT
Supply voltage, VCC 4.5 5.5 V
Voltage at any bus terminal (separately or common mode) VI or VIC –7(1) 12 V
High-level input voltage, VIH D input 0.7 VCC V
Low-level input voltage, VIL D input 0.3 VCC V
Differential input voltage, VID –6 6 V
Input voltage to Rs, VI(Rs) 0 VCC V
Input voltage at Rs for standby, VI(Rs) 0.75 VCC VCC V
Rs wave-shaping resistance 0 100 kΩ
High-level output current, IOH Driver –50 mA
Receiver –4
Low-level output current, IOL Driver 50 mA
Receiver 4
Operating free-air temperature, TA SN65HVD251 –40 125 °C
SN55HVD251 –55 125
Junction temperature, TJ 145 °C
(1) The algebraic convention, in which the least positive (most negative) limit is designated as minimum is used in this data sheet.

6.4 Thermal Information

THERMAL METRIC(1) SN55HVD251 SN65HVD251 UNIT
DRJ (SON) D (SOIC) P (PDIP)
8 PINS 8 PINS 8 PINS
RθJC(top) Junction-to-case (top) thermal resistance 52 44.6 66.6 °C/W
RθJB Junction-to-board thermal resistance 73 78.7 48.9 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953.

6.5 Supply Current

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP(1) MAX UNIT
ICC Supply current Standby Rs at VCC, D at VCC 275 µA
Dominant D at 0 V, 60-Ω load, Rs at 0 V 65 mA
Recessive D at VCC, no load, Rs at 0 V 14
(1) All typical values are at 25°C and with a 5-V supply.

6.6 Electrical Characteristics: Driver

over recommended operating conditions (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP(1) MAX UNIT
VO(D) Bus output voltage (Dominant) CANH Figure 10 and Figure 11 ,
D at 0 V Rs at 0 V, T ≥ –40°C 		2.75 3.5 4.5 V
CANL 0.5 2
VO(R) Bus output voltage (Recessive) CANH Figure 10 and Figure 11 , D at 0.7 VCC,
Rs at 0 V		 2 2.5 3
CANL 2 2.5 3
VOD(D) Differential output voltage (Dominant) Figure 10 , D at 0 V, Rs at 0 V 1.5 2 3 V
Figure 12 , D at 0 V, Rs at 0 V, RNODE = 330 Ω 1.2 2 3.1 V
Figure 12 , D at 0 V, Rs at 0 V, RNODE = 165 Ω, VCC ≥ 4.75 V 1.2 2 3.1 V
VOD(R) Differential output voltage (Recessive) Figure 10 and Figure 11 , D at 0.7 VCC –120 12 mV
D at 0.7 VCC, no load, T ≤ 85°C –0.5 0.05 V
VOC(pp) Peak-to-peak common-mode output voltage Figure 18, Rs at 0 V 600 mV
IIH High-level input current, D Input D at 0.7 VCC –40 0 µA
IIL Low-level input current, D Input D at 0.3 VCC –60 0 µA
IOS(SS) Short-circuit steady-state output current Figure 20, VCANH at –7 V, CANL Open –200 mA
Figure 20, VCANH at 12 V, CANL Open 2.5
Figure 20, VCANL at -7 V, CANH Open –2
Figure 20, VCANL at 12 V, CANH Open 200
CO Output capacitance See receiver input capacitance
IOZ High-impedance output current See receiver input current
IIRs(s) Rs input current for standby Rs at 0.75 VCC –10 µA
IIRs(f) Rs input current for full speed operation Rs at 0 V –550 0 µA
(1) All typical values are at 25°C and with a 5-V supply.

6.7 Electrical Characteristics: Receiver

over recommended operating conditions (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VIT+ Positive-going input threshold voltage Rs at 0 V, (See Table 1) 750 900 mV
VIT- Negative-going input threshold voltage 500 650
Vhys Hysteresis voltage (VIT+ - VIT-) 100
VOH High-level output voltage Figure 15, IO = –4 mA 0.8 VCC V
VOL Low-level output voltage Figure 15, IO = 4 mA 0.2 VCC V
II Bus input current CANH or CANL at 12 V Other bus pin at 0 V, Rs at 0 V, D at 0.7 VCC 600 µA
CANH or CANL at 12 V, VCC at 0 V 715
CANH or CANL at -7 V –460
CANH or CANL at -7 V, VCC at 0 V –340
CI Input capacitance, (CANH or CANL) Pin-to-ground, VI = 0.4 sin (4E6πt) + 0.5 V, D at 0.7 VCC 20 pF
CID Differential input capacitance Pin-to-pin, VI = 0.4 sin (4E6πt) + 0.5 V, D at 0.7 VCC 10 pF
RID Differential input resistance D at 0.7 VCC, Rs at 0 V 40 100 kΩ
RIN Input resistance, (CANH or CANL) D at 0.7 VCC, Rs at 0 V 20 50 kΩ
Receiver noise rejection See Figure 22

6.8 VREF-Pin Characteristics

over recommended operating conditions (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VO Reference output voltage –5 µA < IO < 5 µA 0.45 VCC 0.55 VCC V
–50 µA < IO < 50 µA 0.4 VCC 0.6 VCC

6.9 Power Dissipation Characteristics

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
PD Device power dissipation VCC = 5 V, Tj = 27°C, RL = 60 Ω,
RS at 0 V, Input to D a 500-kHz
50% duty cycle square wave		 97.7 mW
VCC = 5.5 V, Tj = 130°C, RL = 60 Ω,
RS at 0 V, Input to D a 500-kHz
50% duty cycle square wave		 142 mW
TSD Thermal shutdown junction temperature 165 °C

6.10 Switching Characteristics: Driver

over recommended operating conditions (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
tpLH Propagation delay time, low-to-high-level output Figure 13, Rs at 0 V 40 70
Figure 13, Rs with 10 kΩ to ground 90 125
Figure 13, Rs with 100 kΩ to ground 500 800
tpHL Propagation delay time, high-to-low-level output Figure 13, Rs at 0 V 85 125
Figure 13, Rs with 10 kΩ to ground 200 260
Figure 13, Rs with 100 kΩ to ground 1150 1450
tsk(p) Pulse skew (|tpHL - tpLH|) Figure 13, Rs at 0 V 45 85
Figure 13, Rs with 10 kΩ to ground 110 180 ns
Figure 13, Rs with 100 kΩ to ground 650 900
tr Differential output signal rise time Figure 13, Rs at 0 V 35 80 100
tf Differential output signal fall time 35 80 100
tr Differential output signal rise time Figure 13, Rs with 10 kΩ to ground 100 150 250
tf Differential output signal fall time 100 150 250
tr Differential output signal rise time Figure 13, Rs with 100 kΩ to ground 600 950 1550
tf Differential output signal fall time 600 950 1550
ten Enable time from standby to dominant Figure 17 0.5 µs

6.11 Switching Characteristics: Device

over recommended operating conditions (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
tloop1 Total loop delay, driver input to receiver output, recessive to dominant Figure 19, Rs at 0 V 60 100 ns
Figure 19, Rs with 10 kΩ to ground 100 150
Figure 19, Rs with 100 kΩ to ground 440 800
tloop2 Total loop delay, driver input to receiver output, dominant to recessive Figure 19, Rs at 0 V 115 150 ns
Figure 19, Rs with 10 kΩ to ground 235 290
Figure 19, Rs with 100 kΩ to ground 1070 1450
tloop2 Total loop delay, driver input to receiver output, dominant to recessive Figure 19, Rs at 0 V, VCC from 4.5 V to 5.1 V 105 145 ns

6.12 Switching Characteristics: Receiver

over recommended operating conditions (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
tpLH Propagation delay time, low-to-high-level output Figure 15 35 50
tpHL Propagation delay time, high-to-low-level output 35 50
tsk(p) Pulse skew (|tpHL - tpLH|) 20 ns
tr Output signal rise time 2 4
tf Output signal fall time 2 4
tp(sb) Propagation delay time in standby Figure 21, Rs at VCC 500

6.13 Dissipation Ratings

PACKAGE CIRCUIT BOARD MODEL TA = 25°C
POWER RATING		 DERATING FACTOR (1) ABOVE TA = 25°C TA = 85°C POWER RATING TA = 125°C POWER RATING
SOIC (D) Low-K(2) 576 mW 4.8 mW/°C 288 mW 96 mW
High-K(3) 924 mW 7.7 mW/°C 462 mW 154 mW
PDIP (P) Low-K(2) 888 mW 7.4 mW/°C 444 mW 148 mW
High-K(3) 1212 mW 10.1 mW/°C 606 mW 202 mW
WSON (DRJ) Low-K(2) 403 mW 4.03 mW/°C 262 mW 100 mW
High-K
(no Vias)(3) 		1081 mW 10.8 mW/°C 703 mW 270 mW
High-K
(with Vias)		 2793 mW 27.9 mW/°C 1815 mW 698 mW
(1) This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow.
(2) In accordance with the Low-K thermal metric definitions of EIA/JESD51-3.
(3) In accordance with the High-K thermal metric definitions of EIA/JESD51-7.

6.14 Typical Characteristics

SN55HVD251 SN65HVD251 Tloop1VsFAT_lls545.gif Figure 1. Recessive-to-Dominant Loop Delay vs Free-Air Temperature
SN55HVD251 SN65HVD251 IccVsSigRate_lls545.gif Figure 3. Supply Current (RMS) vs Signaling Rate
SN55HVD251 SN65HVD251 Dov_v_Oc2_lls545.gif Figure 5. Driver Differential Output Voltage vs Output Current
SN55HVD251 SN65HVD251 IoVsVcc_lls545.gif Figure 7. Driver Output Current vs Supply Voltage
SN55HVD251 SN65HVD251 r_v_temp_lls545.gif Figure 9. Input Resistance Matching vs Free-Air Temperature
SN55HVD251 SN65HVD251 Tloop2VsFAT_lls545.gif Figure 2. Dominant-to-Recessive Loop Delay vs Free-Air Temperature
SN55HVD251 SN65HVD251 Dov_v_Oc_lls545.gif Figure 4. Driver Output Voltage vs Output Current
SN55HVD251 SN65HVD251 Vod_D_VsFAT_lls545.gif Figure 6. Dominant Differential Output Voltage vs free-Air Temperature
SN55HVD251 SN65HVD251 OFallTmVsRes_lls545.gif Figure 8. Differential Output Transition Time vs Slope Resistance (Rs)