TPA2000D2
- Modulation Scheme Optimized to Operate Without a Filter
- 2 W Into 3- Load
- Extremely Efficient Third Generation 5-V Class-D Technology:
- Low Supply Current (No Filter). . .8 mA
- Low Supply Current (Filter). . .15 mA
- Low Shutdown Current. . .1 µA
- Low Noise Floor. . . 56 µVRMS
- Maximum Efficiency Into 3 , 75-85%
- 4 Internal Gain Settings. . .8-23.5 dB
- PSRR. . .-77 dB
- Integrated Depop Circuitry
- Short-Circuit Protection (Short to Battery, Ground, and Load)
- -40°C to 85°C Operating Temperature Range
The TPA2000D2 is the third generation 5-V class-D amplifier from Texas Instruments. Improvements to previous generation devices include: lower supply current, lower noise floor, better efficiency, four different gain settings, smaller packaging, and fewer external components. The most significant advancement with this device is its modulation scheme that allows the amplifier to operate without the output filter. Eliminating the output filter saves the user approximately 30% in system cost and 75% in PCB area.
The TPA2000D2 is a monolithic class-D power IC stereo audio amplifier, using the high switching speed of power MOSFET transistors. These transistors reproduce the analog signal through high-frequency switching of the output stage. The TPA2000D2 is configured as a bridge-tied load (BTL) amplifier capable of delivering greater than 2 W of continuous average power into a 3- load at 1 kHz, the typical THD+N is less than 0.08%.
A BTL configuration eliminates the need for external coupling capacitors on the output. Low supply current of 8 mA makes the device ideal for battery-powered applications. Protection circuitry increases device reliability: thermal, over-current, and under-voltage shutdown.
Efficient class-D modulation enables the TPA2000D2 to operate at full power into 3- loads at an ambient temperature of 85°C.
技术文档
类型 | 标题 | 下载最新的英语版本 | 日期 | |||
---|---|---|---|---|---|---|
* | 数据表 | TPA2000D2: 2-W Filterless Stereo Class-D Audio Power Amplifier 数据表 (Rev. F) | 2004年 11月 1日 | |||
应用手册 | Measuring Class-D Amplifiers for Audio Speaker Overstress Testing | 2005年 10月 28日 | ||||
用户指南 | TPA2000D2EVM - User Guide (Rev. A) | 2000年 8月 3日 |
设计和开发
如需其他信息或资源,请点击以下任一标题进入详情页面查看(如有)。
TPA2000D2EVM — TPA2000D2 评估模块 (EVM)
The TPA2000D2, is a stereo Class-D audio power amplifier and the first device in TI's new family of filter-free Class-D audio amplifiers. The TPA2000D2 has an output power of 2-Watts RMS or of 4-Watts peak into 4 Ohm speakers. By eliminating the need for bulky LC output filters, TI's new audio (...)
PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice®
借助 PSpice for TI 的设计和仿真环境及其内置的模型库,您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案,然后再进行布局和制造,可缩短产品上市时间并降低开发成本。
在 PSpice for TI 设计和仿真工具中,您可以搜索 TI (...)
封装 | 引脚 | 下载 |
---|---|---|
HTSSOP (PWP) | 24 | 查看选项 |
TSSOP (PW) | 24 | 查看选项 |
订购和质量
- RoHS
- REACH
- 器件标识
- 引脚镀层/焊球材料
- MSL 等级/回流焊峰值温度
- MTBF/时基故障估算
- 材料成分
- 鉴定摘要
- 持续可靠性监测
- 制造厂地点
- 封装厂地点