THS8200-EP

Name: THS8200-EP
Brand: TI
SKU: THS8200-EP
Price: 14.96 USD

正在供货

三通道 10 位全格式视频 DAC（增强型产品）

立即订购

数据表

document-pdfAcrobat All-Format Oversampled Component Video/PC Graphics D/A System 数据表 (英语)

THS8200-EP

正在供货

数据表

立即订购

产品详情

Rating

HiRel Enhanced Product

Supply voltage (V)

3.6

Operating temperature range (°C)

-40 to 85

Rating

HiRel Enhanced Product

Supply voltage (V)

3.6

Operating temperature range (°C)

-40 to 85

HTQFP (PFP)

80

196 mm² 14 x 14

Three 11-Bit 205-MSPS D/A Converters With Integrated
Bi-Level/Tri-Level Sync Insertion
Support for All ATSC Video Formats (Including 1080P) and
PC Graphics Formats (Up to UXGA at 75 Hz)
INPUT
- Flexible 10/15/16/20/24/30-Bit Digital Video Input Interface
  With Support for YCbCr or RGB Data, Either 4:4:4 or 4:2:2 Sampled
- Video Synchronization Via Hsync, Vsync Dedicated Inputs or Via
  Extraction of Embedded SAV/EAV Codes According to ITU-R.BT601
  (SDTV) or SMPTE274M/SMPTE296M (HDTV)
- Glueless Interface to TI DVI 1.0 (With HDCP) Receivers. Can Receive
  Video-Over-DVI Formats According to the EIA-861 Specification and
  Convert to YPbPr/RGB Component Formats With Separate Syncs or
  Embedded Composite Sync
VIDEO PROCESSING
- Programmable Clip/Shift/Multiply Function for Operation With
  Full-Range or ITU-R.BT601 Video Range Input Data
- Programmable Digital Fine-Gain Controller on Each Analog Output
  Channel, for Accurate Channel Matching and Programmable
  White-Balance Control
- Built-In 4:2:2 to 4:4:4 Video Interpolation Filter
- Built-In 2× Oversampling SDTV/HDTV Interpolation
  Filter for Improved Video Frequency Characteristic
- Fully Programmable Digital Color Space Conversion Circuit
- Fully Programmable Display Timing Generator to Supply All
  SDTV and HDTV Composite Sync Ttiming Formats, Progressive
  and Interlaced
- Fully Programmable Hsync/Vsync Outputs
- Vertical Blanking Interval (VBI) Override or Data Pass-Thru
  for VBI Data Transparency
- Programmable CGMS Data Generation and Insertion
OUTPUT
- Digital
  - ITU-R BT.656 Digital Video Output Port
- Analog
  - Analog Component Output from Software-Switchable
    700-mV/1.3-V Compliant Output DACs at 37.5- load
  - Programmable Video/Sync Ratio (7:3 or 10:4)
  - Programmable Video Pedestal
GENERAL
- Built-In Video Color Bar Test Pattern Generator
- Fast Mode I²C Control Interface
- Configurable Master or Slave Timing Mode
  - Configuration Modes Allow the Device to Act as a
    Master Timing Source for Requesting Data from, e.g.,
    the Video Frame Buffer. Alternatively, the Device Can
    Slave to an External Timing Master (Master Mode Only
    Available for PC Graphics Output Modes).
- DAC and Chip Powerdown Modes
- Low-Power 1.8-/3.3-V Operation
- 80-pin PowerPAD™ Plastic Quad Flatpack Package with
  Efficient Heat Dissipation and Small Physical Size
APPLICATIONS
- DVD Players
- Digital-TV/Interactive-TV/Internet Set-Top Boxes
- Personal Video Recorders
- HDTV Display or Projection Systems
- digital Video Systems

PowerPAD Is a trademark of Texas Instruments.

Three 11-Bit 205-MSPS D/A Converters With Integrated
Bi-Level/Tri-Level Sync Insertion
Support for All ATSC Video Formats (Including 1080P) and
PC Graphics Formats (Up to UXGA at 75 Hz)
INPUT
- Flexible 10/15/16/20/24/30-Bit Digital Video Input Interface
  With Support for YCbCr or RGB Data, Either 4:4:4 or 4:2:2 Sampled
- Video Synchronization Via Hsync, Vsync Dedicated Inputs or Via
  Extraction of Embedded SAV/EAV Codes According to ITU-R.BT601
  (SDTV) or SMPTE274M/SMPTE296M (HDTV)
- Glueless Interface to TI DVI 1.0 (With HDCP) Receivers. Can Receive
  Video-Over-DVI Formats According to the EIA-861 Specification and
  Convert to YPbPr/RGB Component Formats With Separate Syncs or
  Embedded Composite Sync
VIDEO PROCESSING
- Programmable Clip/Shift/Multiply Function for Operation With
  Full-Range or ITU-R.BT601 Video Range Input Data
- Programmable Digital Fine-Gain Controller on Each Analog Output
  Channel, for Accurate Channel Matching and Programmable
  White-Balance Control
- Built-In 4:2:2 to 4:4:4 Video Interpolation Filter
- Built-In 2× Oversampling SDTV/HDTV Interpolation
  Filter for Improved Video Frequency Characteristic
- Fully Programmable Digital Color Space Conversion Circuit
- Fully Programmable Display Timing Generator to Supply All
  SDTV and HDTV Composite Sync Ttiming Formats, Progressive
  and Interlaced
- Fully Programmable Hsync/Vsync Outputs
- Vertical Blanking Interval (VBI) Override or Data Pass-Thru
  for VBI Data Transparency
- Programmable CGMS Data Generation and Insertion
OUTPUT
- Digital
  - ITU-R BT.656 Digital Video Output Port
- Analog
  - Analog Component Output from Software-Switchable
    700-mV/1.3-V Compliant Output DACs at 37.5- load
  - Programmable Video/Sync Ratio (7:3 or 10:4)
  - Programmable Video Pedestal
GENERAL
- Built-In Video Color Bar Test Pattern Generator
- Fast Mode I²C Control Interface
- Configurable Master or Slave Timing Mode
  - Configuration Modes Allow the Device to Act as a
    Master Timing Source for Requesting Data from, e.g.,
    the Video Frame Buffer. Alternatively, the Device Can
    Slave to an External Timing Master (Master Mode Only
    Available for PC Graphics Output Modes).
- DAC and Chip Powerdown Modes
- Low-Power 1.8-/3.3-V Operation
- 80-pin PowerPAD™ Plastic Quad Flatpack Package with
  Efficient Heat Dissipation and Small Physical Size
APPLICATIONS
- DVD Players
- Digital-TV/Interactive-TV/Internet Set-Top Boxes
- Personal Video Recorders
- HDTV Display or Projection Systems
- digital Video Systems

PowerPAD Is a trademark of Texas Instruments.

THS8200 is a complete video back-end D/A solution for DVD players, personal video recorders and set-top boxes, or any system requiring the conversion of digital component video signals into the analog domain.

THS8200 can accept a variety of digital input formats, in both 4:4:4 and 4:2:2 formats, over a 3×10-bit, 2×10-bit or 1×10-bit interface. The device synchronizes to incoming video data either through dedicated Hsync/Vsync inputs or through extraction of the sync information from embedded sync (SAV/EAV) codes inside the video stream. Alternatively, when configured for generating PC graphics output, THS8200 also provides a master timing mode in which it requests video data from an external (memory) source.

THS8200 contains a display timing generator that is completely programmable for all standard and nonstandard video formats up to the maximum supported pixel clock of 205 MSPS. Therefore, the device supports all component video and PC graphics (VESA) formats. A fully-programmable 3×3 matrixing operation is included for color space conversion. All video formats, up to the HDTV 1080I and 720P formats, can also be internally 2× oversampled. Oversampling relaxes the need for sharp external analog reconstruction filters behind the DAC and improves the video frequency characteristic.

The output compliance range can be set via external adjustment resistors and there is a choice of two settings, in order to accommodate without hardware changes both component video/PC graphics (700 mV) and composite video (1.3 V) outputs. An internal programmable clip/shift/multiply function on the video data assures standards-compliant video output ranges for either full 10-bit or reduced ITU-R.BT601 style video input. In order to avoid nonlinearities after scaling of the video range, the DACs are internally of 11-bit resolution. Furthermore, a bi- or tri-level sync with programmable amplitude (in order to support both 700/300-mV and 714/286-mV video/sync ratios) can be inserted either on the green/luma channel only or on all three output channels. This sync insertion is generated from additional current sources in the DACs such that the full DAC resolution remains available for the video range. This preserves 100% of the DAC’s 11-bit dynamic range for video data.

THS8200 optionally supports the pass-through of ancillary data embedded in the input video stream or can insert ancillary data into the 525P analog component output according to the CGMS data specification.

THS8200 is a complete video back-end D/A solution for DVD players, personal video recorders and set-top boxes, or any system requiring the conversion of digital component video signals into the analog domain.

THS8200 can accept a variety of digital input formats, in both 4:4:4 and 4:2:2 formats, over a 3×10-bit, 2×10-bit or 1×10-bit interface. The device synchronizes to incoming video data either through dedicated Hsync/Vsync inputs or through extraction of the sync information from embedded sync (SAV/EAV) codes inside the video stream. Alternatively, when configured for generating PC graphics output, THS8200 also provides a master timing mode in which it requests video data from an external (memory) source.

THS8200 contains a display timing generator that is completely programmable for all standard and nonstandard video formats up to the maximum supported pixel clock of 205 MSPS. Therefore, the device supports all component video and PC graphics (VESA) formats. A fully-programmable 3×3 matrixing operation is included for color space conversion. All video formats, up to the HDTV 1080I and 720P formats, can also be internally 2× oversampled. Oversampling relaxes the need for sharp external analog reconstruction filters behind the DAC and improves the video frequency characteristic.

The output compliance range can be set via external adjustment resistors and there is a choice of two settings, in order to accommodate without hardware changes both component video/PC graphics (700 mV) and composite video (1.3 V) outputs. An internal programmable clip/shift/multiply function on the video data assures standards-compliant video output ranges for either full 10-bit or reduced ITU-R.BT601 style video input. In order to avoid nonlinearities after scaling of the video range, the DACs are internally of 11-bit resolution. Furthermore, a bi- or tri-level sync with programmable amplitude (in order to support both 700/300-mV and 714/286-mV video/sync ratios) can be inserted either on the green/luma channel only or on all three output channels. This sync insertion is generated from additional current sources in the DACs such that the full DAC resolution remains available for the video range. This preserves 100% of the DAC’s 11-bit dynamic range for video data.

THS8200 optionally supports the pass-through of ancillary data embedded in the input video stream or can insert ancillary data into the 525P analog component output according to the CGMS data specification.

open-in-new

查找其他 HDMI、DisplayPort 和 MIPI IC

下载观看带字幕的视频视频

技术文档

star

=有关此产品的 TI 精选热门文档

未找到结果。请清除搜索并重试。

查看全部 3

	类型	标题	日期
*	数据表	All-Format Oversampled Component Video/PC Graphics D/A System 数据表	2009年 12月 3日
*	VID	THS8200-EP VID V6210604	2016年 6月 21日
	应用手册	Noise Analysis for High Speed Op Amps (Rev. A)	2005年 1月 17日

设计和开发

如需其他信息或资源，请点击以下任一标题进入详情页面查看（如有）。

仿真模型

THS8200 IBIS Model

SLEM013.ZIP (48 KB) - IBIS Model

下载

模拟工具

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice®

PSpice® for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence® 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助 PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在 PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

发送申请

模拟工具

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)

用户指南: PDF

英语版 (Rev.A): PDF

查看选项

封装	引脚	下载
HTQFP (PFP)	80	查看选项

应遵守 TI 评估类商品的标准条款与条件。

THS8200-EP

三通道 10 位全格式视频 DAC（增强型产品）

THS8200-EP

产品详情

技术文档

设计和开发

THS8200 IBIS Model

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice®

TINA-TI — 基于 SPICE 的模拟仿真程序

订购和质量

支持和培训

可获得 TI 工程师技术支持的 TI E2E™ 论坛

视频系列

视频