ZHCS986B May   2012  – December 2018 TLV320DAC3203

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 描述
    1.     Device Images
      1.      简化方框图
  4. 4 修订历史记录
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics, Bypass Outputs
    6. 6.6  Electrical Characteristics, Microphone Interface
    7. 6.7  Electrical Characteristics, Audio Outputs
    8. 6.8  Electrical Characteristics, LDO
    9. 6.9  Electrical Characteristics, Misc.
    10. 6.10 Electrical Characteristics, Logic Levels
    11. 6.11 Typical Timing Characteristics — Audio Data Serial Interface Timing (I2S)
    12. 6.12 Typical DSP Timing Characteristics
    13. 6.13 I2C Interface Timing
    14. 6.14 SPI Interface Timing (See )
    15. 6.15 Typical Characteristics
      1. 6.15.1 Typical Characteristics, FFT
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Device Connections
        1. 7.3.1.1 Digital Pins
          1. 7.3.1.1.1 Multifunction Pins
        2. 7.3.1.2 Analog Pins
      2. 7.3.2 Analog Audio I/O
        1. 7.3.2.1 Analog Low Power Bypass
        2. 7.3.2.2 Headphone Outputs
      3. 7.3.3 Digital Microphone Inteface
        1. 7.3.3.1 ADC Processing Blocks — Overview
          1. 7.3.3.1.1 Processing Blocks
      4. 7.3.4 DAC
        1. 7.3.4.1 DAC Processing Blocks — Overview
      5. 7.3.5 Powertune
      6. 7.3.6 Digital Audio I/O Interface
      7. 7.3.7 Clock Generation and PLL
      8. 7.3.8 Control Interfaces
        1. 7.3.8.1 I2C Control
        2. 7.3.8.2 SPI Control
    4. 7.4 Device Functional Modes
    5. 7.5 Register Maps
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11器件和文档支持
    1. 11.1 文档支持
      1. 11.1.1 相关文档
    2. 11.2 接收文档更新通知
    3. 11.3 社区资源
    4. 11.4 商标
    5. 11.5 静电放电警告
    6. 11.6 术语表
  12. 12机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6.5 Electrical Characteristics, Bypass Outputs

At 25°C, AVdd, DVdd, IOVDD = 1.8V, LDO_in = 1.8V, AVdd LDO disabled, fs (Audio) = 48kHz, Cref = 10μF on REF PIN, PLL disabled unless otherwise noted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
ANALOG BYPASS TO HEADPHONE AMPLIFIER, DIRECT MODE
Device Setup Load = 16Ω (single-ended), 50pF;
Input and Output CM = 0.9V;
Headphone Output on LDOIN Supply;
INL routed to HPL and INR routed to HPR;
Channel Gain = 0dB
Gain Error ±0.4 dB
Noise, A-weighted(1) Idle Channel, INL and INR ac-shorted to ground 3 μVRMS
THD Total Harmonic Distortion 446mVrms, 1-kHz input signal –82 dB
(1) All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values